Difference between revisions of "Doc:latest/evalguide/build"

Revision as of 03:14, 27 August 2010

Contents

Building the Evaluation System and Deploying Runtime Images

This chapter logically follows from the Installation Guide where we installed the OpenClovis SAFplus Platform SDK. The following sections use the term <install_dir> to refer to the directory in which the SAFplus Platform SDK was installed. By default, this directory is /opt/clovis for root installation and $HOME/clovis for non root users. The following sections describe how to build the evaluation model and deploy the runtime images so that we can run them and observe their behavior.

Building the Target Images

This section describes the steps to:

  • Create a project area
  • Modify OpenClovis sample applications
  • Build SAFplus Platform and the Evaluation System
  • Setup a configuration file to run any of the six Hardware Setups 1.1 to 2.3
  • Create the target image.


Creating a Project Area

To work with the OpenClovis SDK Evaluation System, you will need to use the example project area provided with the SDK. A project area is designed to hold multiple models which share the SAFplus Platform source tree within the SDK installation.

  1. If you have write access to the examples area of the <install_dir> you can simply use this as you project area. In this case your <project_area> would be <install_dir>/sdk-3.0/src/examples.
  2. If you do not have write access to <install_dir>/sdk-3.0/src/examples create a new directory and copy the evaluation system model to it. For example: 
    $ mkdir <new_project_area>
$ cp -r <install_dir>/sdk-3.0/src/examples/eval \
  <new_project_area>/.

    In this case your <project_area> would be <new_project_area>.

In either case your <project_area> should have the following directory structure: 

<project_area>
   |ide_workspace
   |+eval
   |   |+build
   |   |   |+local
   |   |   |   |-Makefile
   |   |+src
   |   |   |+app
   |   |   |+config
   |   |   |+doc
   |   |   |-target.conf
   |   |-Makefile
   |-Makefile

Modifying the Clovis Sample Applications

We have provided the option to modify and rebuild the supplied sample applications.

  1. Modifying sample application code as you see fit:
    The Clovis Sample Application's are located in: <project_area>/eval/src/app
    The source files for the sample application components csa101comp to csa113comp are listed here. Make the necessary alteration to the csa files.
  2. Build the single/distributed target images, as discussed below.


Building SAFplus Platform and the Evaluation System

The next step is to build both SAFplus Platform and the evaluation model in the existing project area.

  1. Configure the eval model for building by running the following: 
    $ cd <project_area>
$ <install_dir>/sdk-3.0/src/SAFplus/configure \
  --with-model-name=eval --with-asp-build

    This will configure the eval model for deployment on the local machine. In order to crossbuild this model for deployment on a non-native target supported by the <crossbuild> toolchain, run: 

    $ <install_dir>/sdk-3.0/src/SAFplus/configure \
  --with-model-name=eval --with-asp-build \
  --with-cross-build=<crossbuild>

    It is possible to configure the model to be built for multiple targets by issuing as many configure commands as necessary. Each run sets up a target-specific build location at <project_area>/eval/build.

    If this model is to be deployed on an ATCA-based system with OpenHPI-based shelf management, enable Chassis Management with: 

    $ <install_dir>/sdk-3.0/src/SAFplus/configure \
  --with-model-name=eval --with-asp-build \
  --with-cross-build=<crossbuild> --with-cm-build=openhpi

    For a complete list of options to configure, including a list of available crossbuild toolchains, run: 

    $ <install_dir>/sdk-3.0/src/SAFplus/configure --help

    If the necessary crossbuild toolchain does not exist, then you must install it by downloading it adjacent to the OpenClovis SDK installer and re-running install.sh.

    The configure step prepares the project area to build the eval model, with the following directory structure: 

    <project_area>
   |ide_workspace
   |+eval
   |   |+build
   |   |   |+local
   |   |   |   |-Makefile
   |   |   |+<crossbuild>
   |   |   |   |-Makefile
   |   |+src
   |   |   |+app
   |   |   |+config
   |   |   |+doc
   |   |   |-target.conf
   |   |+target 
   |   |-Makefile
   |-Makefile
  2. Build the configured model by issuing make in <project_area>/eval: 
    $ cd <project_area>/eval
$ make

    This will build the eval model for all the targets it has been configured to build. In order to do a target-specific build, issue make from the target-specific build location. e.g. for a local build: 

    $ cd <project_area>/eval/build/local
$ make

    For a target supported by the <crossbuild> toolchain: 

    $ cd <project_area>/eval/build/<crossbuild>
$ make

    For a complete list of options to make, run: 

    $ make help

    The model source is located at <project_area>/eval/src. If any changes are made to this, rebuild the model by issuing another make from either the target-specific build location or the top project area directory.

Configuration File - target.conf

Now that the code has been built we are almost ready to build images for deployment to our hardware. But first we must define the target system's configuration so that we build the correct images. A model's target system configuration is specified using a configuration file - target.conf. It is located at <project_area>/eval/src/target.conf. Open this file using your favorite editor (e.g. vi): 

$ vi <project_area>/eval/src/target.conf

This file specifies a number of parameters that need to be defined for a given run-time target:

  1. TRAP_IP (Mandatory): Specifies where the SNMP SubAgent should send traps at runtime. If you do not have an SNMP SubAgent in your model specify 127.0.0.1 as the value. e.g.: 
    TRAP_IP=127.0.0.1
  2. CMM_IP (Mandatory if deployed on an ATCA chassis): Specifies the IP address of the target system's chassis management module or shelf manager. If you are running Hardware Setup 2.1, 2.2 or 2.3 involving PC(s)/Laptop(s) then do not define this variable. ATCA chassis Example: 
    CMM_IP=169.254.1.2
  3. CMM_USERNAME and CMM_PASSWORD (Mandatory if deployed on an ATCA chassis): Specifies the username and password required for the OpenClovis SAFplus Platform Chassis Manager to connect to the target system's chassis management module. e.g.: 
    CMM_USERNAME=root
CMM_PASSWORD=password
  4. INSTALL_PREREQUISITES=YES|NO (Mandatory): Specifies whether the target images will include 3rd party runtime prerequisites or not. Say YES if the target nodes do not meet the target host requirements specified in the Installation section of this document. e.g.: 
    INSTALL_PREREQUISITES=YES
  5. INSTANTIATE_IMAGES=YES|NO (Mandatory): Specifies whether make images will generate node-instance specific images instead of only generating node-type specific images. This option is a development optimization for advanced users of OpenClovis SDK. If unsure, say YES. e.g.: 
    INSTANTIATE_IMAGES=YES
  6. CREATE_TARBALLS=YES|NO (Mandatory): Specifies whether the node-instance specific images created will be packaged into tarballs for deployment onto the target system. If unsure, say YES. e.g.: 
    CREATE_TARBALLS=YES
  7. TIPC_NETID (Mandatory): Specifies a unique identifier used by TIPC to set up interprocess communication across the deployed OpenClovis SAFplus Platform cluster. This is an unsigned 32-bit integer, and must be unique for every model that is deployed. e.g.: 
    TIPC_NETID=1337
  8. Node Instance Details: These specify the node-instance specific parameters required for deploying the model. For each node in the model there is a corresponding entry in the file:
    1. SLOT_<node instance name> (Mandatory): Specifies which slot the node is located in. The first slot is slot 1 -- DO NOT USE SLOT NUMBER 0, it is invalid. When deployed to an ATCA chassis, the physical slot in which the blade is actually installed will override this value. When deployed to regular (non-ATCA) systems, this is a logical slot and must be unique for every node in the cluster. e.g.: 
      SLOT_SCNodeI0=1
    2. LINK_<node instance name> (Optional): Specifies the ethernet interface used by the node for OpenClovis SAFplus Platform communication with the rest of the cluster. If unspecified, this defaults to eth0. e.g.: 
      LINK_SCNodeI0=eth0
    3. ARCH_<node instance name> (Optional if ARCH is specified): Specifies the target architecture of the node as a combination of machine architecture (MACH) and linux kernel version. This is only required on a per-node basis if the target cluster has heterogeneous architectures across the nodes. If it is a homogeneous cluster, a single ARCH parameter (described below) will suffice. e.g.: 
      ARCH_SCNodeI0=i386/linux-2.6.14
    4. ARCH (Optional if node-specific ARCH_ parameters are specified): Specifies the target architecture of all nodes in a homogeneous cluster as a combination of machine architecture (MACH) and linux kernel version. Note: The build process automatically populates this variable based on the last target the model is built for.e.g.: 
      ARCH=i386/linux-2.6.14

    For example, if we have a three-node cluster with the following details:

    Example Node Instance Detail
    Node Name Slot Number Link Interface Architecture
    SCNodeI0 1 eth0 i386/linux-2.6.14
    PayloadNodeI0 3 eth0 i386/linux-2.6.14
    PayloadNodeI1 4 eth1 ppc/linux-2.6.9

    we would specify the node instance details as: 

    SLOT_SCNodeI0=1
SLOT_PayloadNodeI0=3
SLOT_PayloadNodeI1=4

LINK_SCNodeI0=eth0
LINK_PayloadNodeI0=eth0
LINK_PayloadNodeI1=eth1

ARCH_SCNodeI0=i386/linux-2.6.14
ARCH_PayloadNodeI0=i386/linux-2.6.14
ARCH_PayloadNodeI1=ppc/linux-2.6.9
Evaluation Kit 'Node Instance Details' Examples

The 'Node Instance Details' of your target.conf file will be different depending on the hardware setup you are using for your evaluation. Below are some example settings for the various hardware setups.

  1. If you are using single node case as in Hardware Setup 1.1 or 2.1, either using one blade or PC, you set up similar to the following configuration details. Change the slot number accordingly. 
    SLOT_SCNodeI0=1
  2. If you wish to set up a 3 node distributed system, as in Hardware Setup 1.2 or 2.2, your target.conf file may be set up similar to the following configuration details. Again change the slot numbers accordingly. 
    SLOT_SCNodeI0=1
SLOT_PayloadNodeI0=2
SLOT_PayloadNodeI1=3
  3. If you are setting up a 4 node distributed system, as in Hardware Setup 1.3 or 2.3, you would use a configuration that is similar to the following details. 
    SLOT_SCNodeI0=1
SLOT_SCNodeI1=2
SLOT_PayloadNodeI0=3
SLOT_PayloadNodeI1=4

Building Single/Distributed Target Image(s)

This section describes how to build target images for particular Hardware Setups. In essence we provide two types of target image, the System Controller or Payload Node. The images are built with the make images command: 

$ cd <project_area>/eval
$ make images

If target.conf has been configured to instantiate images and create tarballs as recommended, these are populated at <project_area>/target/eval/images. Each node-specific image is provided as a directory containing the run-time files (binaries, libraries, prerequisites, and configuration files) as well as a tarball with the same content. e.g. For a model containing three nodes: SCNodeI0, PayloadNodeI0 and PayloadNodeI1, the following are the files and directories generated for deployment on the run-time system. 

<project_area>
   |+target
       |+<model>
           |+images
               |+SCNodeI0
               |   |+bin
               |   |+etc
               |   |+lib
               |   |+var
               |-SCNodeI0.tgz
               |+PayloadNodeI0
               |-PayloadNodeI0.tgz
               |+PayloadNodeI1
               |-PayloadNodeI1.tgz

Content of Target Images

Content of Single Node Setup

If you chose to create a single node setup then the following directory structure is created. Note it is not the exhaustive directory structure but instead highlights directories and files of importance. 

<project_area>target/eval/images/
   |-target
       |
       |-eval
       |   |images
       |   |   |-generic
       |   |   |   |+bin
       |   |   |   |+etc
       |   |   |   |+lib
       |   |   |   |+modules
       |   |   |   |+share
       |   |   |
       |   |   |-SCNodeI0
       |   |   |   |+bin
       |   |   |   |+etc
       |   |   |   |+lib
       |   |   |   |+modules
       |   |   |   |+share
       |   |   |
       |   |   |-SCNodeI0.tgz

The images directory contains everything required to deploy SAFplus Platform on the chosen runtime setup. In this case, a generic node image and one created specifically for SCNodeI0 are created, both containing the following:

  • bin
    contains executable binaries and scripts, such as asp_amf, asp_console and csa101.
  • etc
    contains XML and text configuration files for SAFplus Platform and third-party tools, as well as an init.d style script to start/stop SAFplus Platform
  • lib
    libraries, including 3rd party dependencies, required by the sample applications
  • modules
    kernel modules (ioc, alarm)
  • share
    contains snmp & mib information

SCNodeI0

Contains the System Controller image to be used for the single node case. This image is to be copied to the target platform.

Content of 3 Node Distributed Setup

If we are building the distributed Evaluation System, additional images for PayloadNode0 and PayloadNode1 are now utilized and this is represented within the content of the directory structure. (When compared to the single node set up, the bold directories/files represent the difference in file structure). 

<project_area>target/eval/images/
   |-target
       |
       |-eval
       |   |images
       |   |   |+generic
       |   |   |
       |   |   |-PayloadNodeI0
       |   |   |   |+bin
       |   |   |   |+etc
       |   |   |   |+lib
       |   |   |   |+modules
       |   |   |   |+share
       |   |   |-PayloadNodeI0.tgz
       |   |   |
       |   |   |-PayloadNodeI1
       |   |   |   |+bin
       |   |   |   |+etc
       |   |   |   |+lib
       |   |   |   |+modules
       |   |   |   |+share
       |   |   |-PayloadNodeI1.tgz
       |   |   |
       |   |   |+SCNodeI0
       |   |   |-SCNodeI0.tgz

PayloadNode0 & PayloadNode1

These additional directories are required for a distributed setup and have a similar structure to SCNodeI0. PayloadNodeI0.tgz and PayloadNodeI1.tgz are the corresponding zipped tar images that are to be copied to the target Payload nodes.

There is nothing special about which node should be the System Controller verses a Payload Node, or which node should be Payload Node 0 verses Payload Node 1. You may copy any tar image to any node -- the contents of the tar image will make the node assume the role. The only exception is, of course, an environment that contains different hardware, for example, an Intel-based machine and a PowerPC based machine. In that case you need to define your ARCH variables correctly (see above) and deploy images only to matching hardware.

Content of 4 Node Distributed Setup

If we are building the 4 node distributed Evaluation System, the additional image SCNodeI1 is now created and this is represented within the content of the directory structure. (When compared to the 3 node distributed set up, the bold directories/files represent the difference in file structure) 

<project_area>target/eval/images/
   |-target
       |-eval
       |   |images
       |   |   |+generic
       |   |   |
       |   |   |+PayloadNodeI0
       |   |   |-PayloadNodeI0.tgz
       |   |   |+PayloadNodeI1
       |   |   |-PayloadNodeI1.tgz
       |   |   |+SCNodeI0
       |   |   |-SCNodeI0.tgz
       |   |   |
       |   |   |-SCNodeI1
       |   |   |   |+bin
       |   |   |   |+etc
       |   |   |   |+lib
       |   |   |   |+modules
       |   |   |   |+share
       |   |   |
       |   |   |-SCNodeI1.tgz

SCNodeI1

These additional directories are required for a distributed setup and have a similar structure to SCNodeI0. SCNodeI1.tgz is the corresponding zipped tar image that needs to be copied to the second System Controller.


Runtime Software Installation

The hardware setups require steps to copy the runtime images from the Development Machine to the Runtime target machine(s). The following describe the necessary steps required to copy runtime images to the desired target(s).


Installing SCNodeI0

  1. On the Development Machine locate the target images 
    $ cd <project_area>/target/eval/images
  2. Copy the zipped tar System Controller image to the desired target. 
    $ scp SCNodeI0.tgz root@<SystemController IPAddress>:/root/

    Enter password. 

     # ssh root@<SystemController IPAddress>

    Enter password 

     # cd /root
 # mkdir asp
 # cd asp
 # tar xzvf ../SCNodeI0.tgz

    This unzips and extracts the contents of SCNodeI0.tgz within /root/asp. The System Controller is now installed on the target.

    OpenClovis Note.png This step is necessary even if the System Controller and Management Machine are the same PC (As in Runtime Hardware Setup 2.1)

    If you are setting up a 4 node distributed setup, as in 'Runtime Hardware Setup 1.3.' repeat the above steps, replacing the IP address with SCNodeI1's and securely copying SCNodeI1.tgz.


Installing PayloadNode0 and PayloadNode1

Perform the following, if the distributed Hardware Setup 1.2, 1.3, 2.2 and 2.3 is chosen:

  1. On the Development machine locate the Target images 
    $ cd <project_area>/target/eval/images
  2. Copy the zipped tar PayloadNode0 image to the desired target. 
    $ scp PayloadNodeI0.tgz root@<PayloadNode0 IPAddress>:/root/

    Enter password. 

    # ssh root@<PayloadNode0 IPAddress>

    Enter password 

    # cd /root
# mkdir asp
# cd asp
# tar xzvf ../PayloadNodeI0.tgz

    This unzips and extracts the contents of PayloadNodeI0.tgz within /root/asp The PayloadNode0 is now installed on its target. For PayloadNode1 repeat the above 2 steps, replacing the IP address with PayloadNode1's and securely copying PayloadNode1.tgz.

Summary and Next Steps

This chapter covers a number of possible hardware configurations and the steps required to build and install the target images. Chapter Sample Applications, covers all the Evaluation applications that can be run. For each Sample Application, a description on its objective, what you will learn, key areas of code, how to run it, sample output and conclusion is provided.

Retrieved from "https://help.openclovis.com/index.php?title=Doc:latest/evalguide/build&oldid=541"